Ir directamente al contenido principal
fastmerc

fastmerc

4,7 mil artículos vendidos
97 seguidores
Contactar

Todos los artículos

Artículos por página
Ver todo

Acerca de

Ubicación: Estados UnidosUsuario desde: 29 dic 1998

Total de votos

Últimos 12 meses

Positivos68- Votos positivos durante los últimos 12 meses
Neutros0- Votos neutros durante los últimos 12 meses
Negativos0- Votos negativos durante los últimos 12 meses

Valoraciones detalladas sobre el vendedor

Promedio durante los últimos 12 meses

Descripción precisa
5.0
Gastos de envío razonables
4.8
Rapidez de envío
5.0
Comunicación
5.0

Todos los votos (4.296)

e***n (156)- Votos emitidos por el comprador.
Mes pasado
Compra verificada
These items I bought are hard to find in this shape, pure luck I found them, also there in great shape for there age thank you.. Larry
gjsrr (387)- Votos emitidos por el comprador.
Mes pasado
Compra verificada
Courteous and prompt transaction
a***s (904)- Votos emitidos por el comprador.
Mes pasado
Compra verificada
Just as described works great, fast shipping.
e***n (156)- Votos emitidos por el comprador.
Mes pasado
Compra verificada
He has the part I was looking for, was in great condition thanks again
scol22785 (1549)- Votos emitidos por el comprador.
Mes pasado
Compra verificada
Thanks for a pleasant transaction. Your purchase is appreciated!!
x*flare (2568)- Votos emitidos por el comprador.
Mes pasado
Compra verificada
Good buyer, prompt payment, valued customer, highly recommended.
Ver todos los votos
Opiniones (20)
Brake Master Cylinder-PG Plus Professional Grade New Raybestos MC36251
19 may 2017
Just installed it, so far so good!
Nice part, all new construction, comes with bleeder kit also! All machining is crisp with no flashing or buggered up threads.
Dorman 594-275 - Solutions Harmonic Balancer
28 dic 2017
Who know's what you'll get! NOT for a 1969 351W!!! 1970+ is just fine but it depends....
Here is why I do NOT recommend this part!!!! This part does NOT work on a 1969 351W unless you change the crank pulley, water pump pulley, timing cover, timing marker, and the water pump....then the radiator..... 1969 balancer should have 3 pulley mounting holes, 1970+ should have 4 holes. This part DOES fit 1970 and up 351W cars just fine! UNLESS, you get a 302 part in the box like I did.....which doesn't fit any of the 351's properly. Site pictures vary widely for this part, some clearly showing 1970 4 hole version, others showing nothing but one side shot which is NOT a 351W balancer. Not sure who made the mistake, but it is being spread like a bad case of.....spoiled beer. Buyer beware!
Whirlpool 21001108 WHIRLPOOL MAYTAG WASHER MOTOR PULLEY 21001108 Part # 21001108
05 ene 2016
All you can get!
This is one of those "replaces a few parts" ......parts! In my case, I am rating this low, as it is a smaller diameter than the original pulley, which decreases the spin speed.....which was my problem..not spinning out the water. This also doesn't just slide on like you would expect a good replacement part to fit. You will probably need to use a hammer and a wood block to get it on without damaging the motor shaft. I never installed mine....I eventually found a proper replacement piece, but it is discontinued part, and I got lucky. Otherwise, this is a good part, made well, and others have seemed to make it work. Just not for me this time........ If I have to do this again, I would need to use this piece!
Ver todas las opiniones